A choice of fixed and operable combinations are available that will optimize site lines while maintaining architectural integrity. Note that this is especially important when considering the effects of grille design.
Shall be 325 Series as manufactured by INLINE FIBERGLASS Ltd. Frames are 3-1/4" (82.5 mm) deep in compliance with AAMA 101/I.S.2, CAN/CSA-A-440.1 and CSA-A-440.2 standards. Rating [CSA 440 A3/B7/C4] [AAMA HC-55].
Materials
All frame and sash profiles are made from Pultruded Fiberglass, having a nominal of wall thickness of 0.090" (2.3 mm), with minimum glass content of 60%. Non-structural accessory members are premited to be in vinyl or aluminum and are identified as such.
Construction
Frame and sash corners are connected with moulded reinforced polyester sherblocks and mechanically secured. All joints are factory sealed and neatly fitted together. The perimeter of open-back frames shall be filled with insulation.
Finish
The exposed surfaces are coated with durable lsocynate-free 2 part Polymer Enamel with minimum dry film thickness of 1.5 mils and medium gloss of 25.55. Finish shall resist chipping, blistering, chalking, discoloration and aging under all atmospheric conditions. Conforms to AAMA 613 Organic Coatings. Standard colors are White, Ivory, Sandalwood, Commercial Brown and Forest Green. (Custom colours and split frame painting is available).
Hardware
Concealed Stainless Steel Hinges, E-Gard Roto Gear Operators and metal Cam ( optional multi-pocket locks ) are manufactured by "TRUTH Hardware". Hardware is installed with fasterners into patented back-up reinforcements.
Weather-Stripping
Q-Lon air-seal gasket on interior with Santoprene bulb-type "rain screen" gasket on the exterior to provide weather barrier
*Note- To be rewritten based on changes to spec. & product.
Glass
All windows are glazed with 7/2" (22 mm) ( or 1-3/8" (35mm) (for triple glazed) insulating glass units. Glass thickness shall comply with local National Building Codes, but not less than 3 mm (1/8"). Units are assembled with a dual seal (polysulphide/Butyl) to CGSB 12.8-90 and Certified by inspection by the Insulated Glass Manufacturers Association.
Glazing Method
Laid-in glazing using polyethylene closed cell tape or shimmed butyl on the exterior and a PVC glass stop locked-in from the interior provides a secure and positive seal for the glass.
Insect Screen
Roll-formed aluminum frame with friction fit corner keys. Screen mesh (Fiberglass or Aluminum) is held in place by spline, Screens are mounted on the interior and are removable.
Installation
Shall be performed by experienced installers in accordance with manufacturer instructions and CSA A-440.4 Standards. Window shall be plumbed and square after installation is complete and sealed to both interior and exterior wall with high quality sealant around the perimeter of the frame. If perimeter cavity is to be foamed, additional anchorage may be required to prevent bowing. It shall be the responsibility of the installers to make all the necessary final adjustments to ensure normal and smooth operation.
Maintenance
Occasional cleaning of glass and frame components with non-abrasive detergent is recommended.
| Laboratory Test Size | Casement | Awning | Fixed |
| CSA Size | 700mm x 1600mm | 1000mm x 1000mm | 1816mm x 2020mm |
| AAMA Size | 27-1/2" x 63" | 39-3/8" x 39-3/8" | 71-1/2" x 79-1/2" |
| Type | Test | Standard |
|
Results | Rating | |
| Test Standard | Test Criteria | |||||
| O P E R A T O R |
Air Tightness | CSA-A440 | ASTM E 283 | @ 75 Pa | 0.04 m3/h/m | A3 |
| AAMA | ASTM E 283 | @ 1.57 psf | 0.01 cfm/ft2 | PASS | ||
| Water Tightness | CSA-A440 | ASTM E 547 | @ 700 Pa | No Leakage | B7 | |
| AAMA | ASTM E 547 | @ 14.5 psf | No Leakage | HC-90 | ||
| Wind Load Resistance | CSA-A440 | ASTM E 330 | @ 4000 Pa | No Deform. | C4 | |
| AAMA | ASTM E 330 | @ 84 psf | No Damage | HC-55 | ||
| Forced Entry | CSA-A440 | ASTM F 588 | No Entry | No Entry | F2 | |
| AAMA | ASTM F 588 | No Entry | No Entry | Gr. 10 | ||
| x | ||||||
| F I X E D |
Air Tightness | CSA-A440 | ASTM E 283 | @ 75 Pa | 0.02 m3/h/m | FIXED |
| AAMA | ASTM E 283 | @ 1.57 psf | 0.01 cfm/ft2 | PASS | ||
| Water Tightness | CSA-A440 | ASTM E 547 | @ 700 Pa | No Leakage | B7 | |
| AAMA | ASTM E 547 | @ 14.5 psf | No Leakage | HC-90 | ||
| Wind Load Resistance | CSA-A440 | ASTM E 330 | @ 5000Pa | No Deform. | C5 | |
| AAMA | ASTM E 330 | @ 105 psf | No Damage | HC-70 | ||
| Forced Entry | CSA-A440 | ASTM F 588 | No Entry | No Entry | F2 | |
| AAMA | ASTM F 588 | No Entry | No Entry | Gr. 40 | ||
Energy Ratings
The Thermal Performance Values, shown below, are based on products glazed with insulating glass units comprising one lite of Low-E glass, an argon-filled cavity and a double-sealed aluminum spacer.
Higher performance may be achieved by using various glass coatings, inert gasses and/or warm edge spacers.
Ratings are computer simulated in accordance with CSA-A440.2. NFRC values are interpolated from CSA A440.2 simulations.
| Energy Performance | Operating | Fixed | ||
| CSA-A440.2 | NFRC | CSA-A440.2 | NFRC | |
| U-Value (frame) | 1.43 W/m2/C | 0.26 BTU/h/ft2/F | 1.64 W/m2/C | 0.34 BTU/h/ft2/F |
| U-Value (window) | 1.80 W/m2/C | 0.32 BTU/h/ft2/F | 1.84 W/m2/C | 0.35 BTU/h/ft2/F |
| SHGC | 0.49 | 0.49 | 0.63 | 0.63 |
| Energy Performance | -4 W/m2 | N/A | -4 W/m2 | N/A |
Note: The reader is cautioned that test results should be used for comparison purposes only. Results are size and installation dependent. In-service performance can be significantly different from those shown.